coppercutlass

Its a .030 over 350 now 355. crank is turned .10 on the rods and .020 on the mains, it has king bearings, speed pro flat top pistons and rings , It has been balanced., bored and honed with tq. plates. It has a howards 512/512 224/237 cam , comp double roller timing set, comp push rods, guide plates, studs, prw roller tip rockers. The cylinder heads where built 2 years ago and only ran for maybe 5000 miles they where done by rocker racing i stil have the recipts. They #6 heads with 2.072 in. and 1.68 ex. valves with oversized springs all new keepers and retainers, guides. The heads where milled .022 to get the compression right around 10 to 1 with a .040 head gasket. On top sits a edelbrock rpm intake milled to fit the heads. It has a std. volume oil pump from melling along with a 5Qt big block pan w/ baffle. Im looking for 2800 It cost me a little over 3500 to build this engine it has never ran and for the price you can still take it to a shop and have it inspected if you wish to do so.

Rickman48

I thought this was your 'forever' street motor.
What changed your mind?

coppercutlass

Got a smoking deal I could not pass up now there is a change of plans. I'd hate to see the engine go but this will offset my cost's with the new car which came with a bbo.

rocketboy

do you know if the block was decked to 0 also or if just the heads where shaved?

coppercutlass

pistons are .025 in the cylinders. with the chambers being roughly 67 cc's compression falls right around 9.9 to 1 .

oldcutlass

Ok, speel yer guts, what's the new plan?

coppercutlass

Can't say much as an agreement with the owner. But once we completly hash out the deal. I will post it up.

gearheads78

I know Nuffing. Nuffing I say

coppercutlass

lol.

coppercutlass

thread bump !

BIGJERR

He did get a deal.....somebody is a nice guy
<<<<<<<< ;-)

oldcutlass

Annnnnnnd the plot thickens.

coppercutlass

jerr It's the deal of the cetury for me . I cant thank you enough.

815Cutlass1972

Deal almost complete?

coppercutlass

Almost. I think. You looking to buuy my 350 ?

815Cutlass1972

I was just gettung anxious to find out what deal you got. LOL.... I will be looking to buy a SBO or BBO in the near future. I just bought a 72 442 Roller a few days ago.

coppercutlass

Well my sbo is still for sale.

coppercutlass

not for sale put wrong post on wrong thread lol

coppercutlass

Bump. Im planning on selling this engine if someone is interested . It's still in the car it runs great. I plan on leaving it in until someone is interested. Im looking at a new project car and I have another engine I want to build and im going in a totally different direction with the whole deal . If anyone is interested I think 2k is the bare bones bottom. That leaves you with enough room if you wanted to get the engine inspected by a shop. I built this engine im no professional but I did it carefully and took all the steps I could to ensure it would perform properly. If anyone interested wants to come by and take it for a drive I welcome that. Im not in a rush but if it sells it sells. I might add this engine runs really strong. I fired it up in april and it might have 1k miles on it. odomerter is busted but I have beend riving it around town and cruising it. I might add the bottom end alone cost me 2k to build. The heads and intake ran me about 1600 all said and done at the time they where re built.

coppercutlass

ttt

z11375ss

Hey Copper. GLWTS, and your future Ninja project.

coppercutlass

bump

z11375ss

It's probably cheap, borrowed and stolen! Lol! You can't argue with success my friend. That motor is badass. I know you don't listen to those dorks, but don't listen to those dorks. Crybabies. If I ever have anything I think you a need I will of course give you a call. Glwts!